Free tool · 10 questions · Live result

Is my wall load-bearing? Read the clues, then get it checked.

Knocking two rooms into one starts with a simple question that has no simple answer.

Some clues you can check yourself — where the wall is, how it sounds, which way the joists run, what sits above it. Answer what you can and we’ll show you what they suggest, and why. Whatever the result, a structural engineer has the final word before any wall comes out.

Check your wall

01Where is the wall?

A party wall is the one you share with the house next door in a terrace or semi.

02Knock on it. Does it sound solid or hollow?

Knock with your knuckles in a few places, away from door frames and sockets.

03How thick is the wall?

Measure across the wall at a doorway, including the plaster both sides. Take off any door lining or architrave.

04Which way do the joists run above it?

Floorboards are laid at right angles to the joists under them, and the rows of nails in the boards follow the joists. Check the floor upstairs, look at the ceiling joists from the loft, or lift a loose board.

05Is there a wall directly above or below it?

Check the room upstairs, and the cellar or ground floor if you’re upstairs. “Directly” means in the same line.

06Does it run down the middle of the house?

A spine wall runs roughly through the centre, splitting the house into front and back (or left and right) halves.

07Is there a chimney breast in or on this wall?

A chimney breast is the projecting section of wall around a fireplace, even if the fireplace has been blocked up.

08Is it part of the original house?

Walls added later — to make a bathroom, split a bedroom or convert a house — are often lighter.

09What’s above it in the loft?

Only relevant if the wall is on the top floor. Look in the loft along the line of the wall, with a torch and boards to stand on.

10Roughly how old is the house?

Not sure? Date it from the clues with our How old is my house? tool.

Side by side

Clues and what they suggest.

Each clue nudges the odds. None of them, on its own, proves a wall is or isn’t carrying load.

Clues that a wall is load-bearing, and their limits
ClueHow to checkSuggests load-bearing when…But bear in mind
PositionIs it an outside wall, or shared with next door?It’s an outside wall or a party wallAlmost all are structural; openings always need a designed lintel or beam
SoundKnock in several placesSolid, dull and unmoving (masonry)Masonry partitions exist, and timber stud walls can carry load
ThicknessMeasure at a doorway, plaster to plasterAbout 250 mm or more — a full brick or stone wallA 125–150 mm solid wall could be either
JoistsFloorboards run at right angles to joists; check upstairs, in the loft or under a lifted boardJoists end, join or overlap on the wall, or cross itParallel joists usually mean no load from that floor, but not always
Walls above and belowLook upstairs and in the cellar for a wall in the same lineA wall stands directly on it, or it stands on oneA designed beam may already carry the wall above
Spine wallDoes it run through the middle of the house?It splits the house into halvesShort cupboard and en-suite walls are more often partitions
Chimney breastA projecting section, even with the fireplace blockedThere’s a breast in or on the wallRemoving one always needs approval and designed support
Original or addedOld plans, the seller, a change in plaster or skirtingIt’s original to a terrace or semiLater walls can pick up load or be built under a beam that relies on them
RoofIn the loft, follow the line of the wallStruts or props from the purlins land on itTrussed rafters usually span the outside walls — unless altered
AgeOur house age toolOlder houses, built with cut roofs and solid wallsOver decades, partitions can take load as timbers sag

The joist test

How to tell which way the joists run.

Floor joists are the timber beams that carry each floor and the ceiling below it. The floorboards are nailed across them at right angles, so the boards tell you the joists’ direction: if the boards run parallel to your wall, the joists cross it.

  • Upstairs: lift a carpet corner and look at the boards. The rows of nail heads follow the joists below.
  • In the loft: the ceiling joists of the top floor are on show. See whether they cross the line of the wall, and whether they stop, join or overlap over it.
  • Lifting a board: a loose board, or one already cut for pipes, lets you see the joists and whether they rest on the wall. Watch for cables and pipes underneath.
  • Under the floor: from a cellar, you can often see the ground-floor joists and where they bear.

Joists that cross a wall aren’t automatically relying on it, and joists that run parallel don’t rule it out. Older houses have been altered, joists may have been doubled or trimmed, and timbers that have deflected over decades can come to rest on a partition that was never meant to carry them.

Joists running across a wall and resting on itAn exploded cutaway. The floor, lifted above the wall to show what is underneath, has joists running across the line of the wall. Dashed lines drop from each joist to the ochre bearing points on top of the wall where it rests. Floorboards run across the joists, parallel to the wall, and another wall stands directly above. This wall is likely load-bearing.Floorboards runacross joistsWalldirectly aboveJoistsBearing:joists reston the wall
  • Floorboards
    across joists
  • Wall directly
    above
  • Joists
  • Joists rest on wall
  1. Floorboards run across the joists
  2. Wall directly above
  3. Joists
  4. Bearing (in ochre): the joists rest on the wall
Fig. 3a · Joists acrossIllustrative exploded cutaway: the joists cross the wall and rest on it.

Likely load-bearing

Joists running parallel to a wall and not resting on itAn exploded cutaway. The floor joists run in the same direction as the wall, passing either side of it without touching, and span to other supports. The floorboards run across the joists, at right angles to the wall. There is no wall above. This wall is less likely to be load-bearing, though not ruled out.Floorboards runacross joistsJoists span toother wallsNothingrests on it
  • Floorboards
    across joists
  • Joists span
    other walls
  • Nothing rests on it
  1. Floorboards run across the joists
  2. Joists span to other walls
  3. Nothing rests on the wall
Fig. 3b · Joists parallelIllustrative exploded cutaway: the joists run beside the wall and do not touch it.

Less likely

In the loft: trussed rafters compared with a traditional roofTwo roof sections, one above the other. Above: a modern trussed rafter roof, where factory-made triangulated trusses span from one external wall to the other and the internal wall below carries no roof load. Below: a traditional cut roof, where a purlin supports the rafters and a strut, highlighted, runs down from the purlin onto an internal wall, so that wall carries roof load.
  • Trussed rafters
  • Clear: no roof load
  • Traditional
    roof
  • Struts
  • Purlin
  1. Trussed rafters span wall to wall
  2. Clear: the internal wall carries no roof load
  3. Traditional roof: struts down onto an internal wall
  4. Struts (in ochre)
  5. Purlin
Fig. 3c · In the loftIllustrative roof sections: trussed rafters above, a traditional roof below.

Floorboards run across the joists, so the boards tell you which way the joists go. Where joists cross a wall and rest on it, with another wall directly above, the wall is likely carrying load. Where they run parallel and don’t touch it, it’s less likely — but not ruled out. In the loft, roof struts coming down onto an internal wall are another sign it carries load.

Before you knock through

What removing a wall actually involves.

  1. An engineer’s design. A structural engineer confirms what the wall carries and designs the beam, its bearings and any padstones, with calculations. Planning Portal notes a new beam normally needs at least 150 mm of bearing on each side, and padstones may be needed to spread the load.
  2. Building Regulations approval. Removing a load-bearing wall alters the structure, so building control approval and inspection are required. Even a non-load-bearing wall may need approval if it affects fire escape routes, ventilation, drainage or electrics.
  3. The Party Wall Act, if it applies. Cutting into a party wall to take a beam is notifiable work. See do I need a party wall notice? and our guide to party wall agreements.
  4. Temporary support. Before the wall is touched, the builder props the structure above — usually adjustable steel props, often with needles through the wall — and keeps it supported until the new beam is in and carrying the load.
  5. A completion certificate. Keep it with the engineer’s calculations. You’ll need both when you sell.

Chimney breasts are a special case — see our chimney breast removal guide. We can talk through your plans in a building advice session, and keep an independent eye on the work with extension and renovation oversight. We don’t design beams; a structural engineer does.

Common questions · walls

Load-bearing walls.

How can I tell if a wall is load-bearing?

Look for clues: outside walls and walls shared with next door almost always carry load; so do walls that floor joists rest on, walls with another wall directly above them, walls with a chimney breast, and walls that roof struts come down onto in the loft. Thick, solid walls running through the middle of the house are often structural. No single clue is conclusive, so a structural engineer should confirm it before any work.

Can a stud wall be load-bearing?

Yes. Many timber stud walls are simple partitions, but some carry floor joists or roof loads — particularly in older houses and in timber-framed homes. A hollow sound when you knock on a wall tells you how it is built, not what it carries.

Do I need Building Regulations approval to remove a wall?

To remove or alter a load-bearing wall, yes: Planning Portal and LABC both say it needs building control approval because you are altering the structure, and you will need a structural engineer’s calculations for the beam. Removing a non-load-bearing wall will often not need approval, provided it does not affect fire escape routes, ventilation, drainage or electrics — but Planning Portal recommends getting an engineer to confirm it is non-load-bearing first.

Who decides what size beam I need?

A structural engineer. The beam, the length it sits on each wall (its bearings), any padstones and whether the walls and foundations below can take the extra load all come from their calculations, which building control will check. A builder’s rule of thumb or a supplier’s span table is not a substitute.

Do I need a party wall agreement to knock through?

Only if the work involves a party wall — for example, cutting into it to sit one end of a new beam on it. That is notifiable under the Party Wall etc. Act 1996 even if you only cut into your own side, and notice for party wall work must be given at least two months before it starts. Knocking through between two of your own rooms, with no work to the shared wall, does not usually involve the Act.

Sources and further reading

Where this comes from.

  1. Building Regulations: load-bearing wallsPlanning Portal on removing load-bearing and non-load-bearing walls.
  2. Building Regulations: structural supportPlanning Portal on beams, bearings and padstones.
  3. What Building Regulations apply to internal walls?Planning Portal’s overview.
  4. Do I need building control approval for internal alterations?LABC’s homeowner guidance.
  5. Roof truss “alterations”LABC on why cut trusses can shift roof loads onto internal walls.
  6. Party walls and building work: when and how to tell themGOV.UK on notice periods.
  7. Party Wall etc. Act 1996, section 2The rights to cut into a party structure.

Planning to knock through?

Get it checked first.

Book a building advice session to talk through the wall, the clues and who you need — then, if the work goes ahead, we can oversee it stage by stage. Any beam is designed by a structural engineer.

Fixed quote before you commit

We aim to reply within one working day.